Nissan Maxima Recalls

This recall is for certain vehicles that had an airbag inflator replaced as a part of an earlier recall campaign. This recall provides a final repair. Long-term exposure to high ab

On certain vehicles, the antilock brake system (ABS) actuator pump may leak brake fluid and malfunction. This would cause the ABS warning lamp to turn on. If this problem is not fi

Issue: On certain vehicles, the rear view camera system does not return to the default setting when the transmission is shifted to reverse. This could cause a reduction in rear vis

On certain vehicles, the antilock brake system (ABS) actuator pump may leak brake fluid onto an electronic circuit board, causing it to malfunction. This would cause the illuminati

Certain vehicles may have been fitted with an incorrect Occupant Classification System (OCS) module. An incorrect OCS module would impair the effectiveness of the OCS, potentially

Certain vehicles equipped with Intelligent Cruise Control may have ABS actuators that may have been manufactured out of specification. This could cause the ABS actuator pump seal t

On certain vehicles, a defect in the occupant classification system could allow an adult sitting in the front passenger seat to be classified as a child or an “empty seat”. This wo

Certain vehicles may have been manufactured with a defective Anti-Lock Braking System (ABS) actuator. This could cause pressure control to be delayed when the Anti-Lock Brakes are

On certain vehicles, the sealing ring between the fuel sending unit and the fuel tank may move out of position in a crash. This could increase the potential risk of a fuel leak in

On certain vehicles, the O-ring between the fuel sending unit and the fuel tank may not have been seated correctly at the time of assembly. This could increase the potential risk o

On certain vehicles, the passenger (frontal) airbag inflator could produce excessive internal pressure during airbag deployment. Increased pressure may cause the inflator to ruptur

On certain vehicles, the passenger (frontal) airbag inflator could produce excessive internal pressure during airbag deployment. Increased pressure may cause the inflator to ruptur

On certain vehicles, the metal upper strut insulators may have been manufactured incorrectly and, as a result, could fail. In the worse case this could allow the strut rod to come

Certain vehicles fail to comply with the requirements of CMVSS 114 - Locking and Immobilization Systems. The steering wheel lock may engage with the ignition in the "OFF" position,

The die used for stamping the rear suspension subframe was out of specification during three days of production. As a result, the thickness of the attachment bracket for the rear l

On certain vehicles equipped with a driver seat power lumbar support, if the wire harness from the lumbar switch is routed incorrectly, the harness could be pinched or chafed again

On certain vehicles, the glass for the Skyview Roof may not have been quenched properly after the forming process resulting in temper imbalance. This could create extensive interna

On certain vehicles, the circuit board for the crank position sensor may have an improper solder joint. This could cause the Service Engine Soon warning light to come on, create a

On certain vehicles one of the diodes used in the alternator may have been damaged when built. This can eventually result in failure of the diode and an electrical short, which cou

On certain vehicles the pin at the inboard end of the front lower control arm may break. This may result in difficulty in directional control and tire contact with the inner fender

Certain passenger vehicles equipped with an electronic throttle control system. The stopper for the accelerator pedal will prevent excessive movement of the accelerator position se

TRAPPED MUD AND SALT CAN RESULT IN CORROSION OF THE FUEL FILLER TUBE AND THE WHEEL HOUSING. SIGNIFICANT CORROSION OF THE FUEL FILLER TUBE MAY RESULT IN FUEL LEAKS WHICH, IN THE PRE

THE CLEAR COAT ON THE ALUMINUM WHEELS MAY BE THICKER THAN DESIRED. WHEEL NUTS ON A WHEEL WITH EXCESSIVE CLEAR COATING MAY LOOSEN OVER TIME BECAUSE THE CLEAR COAT LAYER COMPRESSES U

THERE IS THE POSSIBILITY THAT THE AIRBAG MAY DEPLOY AS THE RESULT OF UNDERBODY IMPACTS. THIS COULD RESULT IN LOSS OF DRIVER CONTROL. CORRECTION: TUNNEL SENSOR WILL BE REPLACED ON A